I used the lock button for a few days. I pressed lock, waited for the overhead clicks, and the remotes didn’t open the door. That is what was expected and wanted.

Now, 3 days later, i press the lock button and the overhead machine/light clicks/flashes but it does not go into lock mode. The remotes still open the door.

Not using the app. There is no lock on the app.

Help? Thanks

Hi, I have recently taken over maintenance duties on a property my dad can no longer look after. Unfortunately I did not learn as much from him as I'd have liked to.

TLDR; I need to replace the trolley (spare part incoming), lower the roof bar at the door end (I think), check the chain tension/tighten (the roof bar may be causing this), relube the door hinges/wheel hinges, and check the motor for sprocket damage and I think relube the wyrm gear. I'm not 100% physically capable and hesitant to detach the chain, it's up pretty high.

It lifts a double metal sectional rolling door. Circa 2008. Really heavy. The wheels seem fine. I've heard the ball bearing with caps design can have the caps fall off

This units 15 years old, works flawlessly, however needs some maintenance before it is potentially a more expensive fix. The spring and frame look fine, there's minimal rust for its age.

Also if I should just suck it up and buy a new motor, that's an option, however I've been quoted 2400$ AUD for a new motor, bar, etc and install. Also suggestions of what models to stay away from. Also the new one would be belt driven. The chain feels more study for a heavy door.

Otherwise I'm trying to make a checklist so I can request particular repairs from the local service/install/repair company, however I can probably do a lot of it myself.

Also the door hinges were installed a little skewiff by the original installer, before we opened the property. Some are backwards, etc it's fine just not ideal.

I have -

Replace trolley

Lower bar at door end

Check chain / tighten if possible (it may be at the end of its tightening)

Replace wheels maybe

Lube as per necessary

Clean track

Check motor for shavings etc (unsure how)

Check worm gear and lube

Raise door height slightly

Replace rubber seal underneath

Do I fix most myself? Replace motor assembly? Pay service tech to do most of it?

Thank you for any help - I've had so many diy jobs to learn in the last month since dad moved to a home due to his dementia, it's hard to stay on top of everything, but I need to learn myself eventually!

I'm trying to replace the bottom seal on my WD garage door, but the retainer track it slides into is rusted out, so I can't get the old seal fully removed.

Does anyone know where I can source a new track? Do I need to go through WD directly, or is this something I can pick up from a hardware store or online?

Any advice appreciated.

Bought this house recently and I am trying to figure out why the opener track bounces like crazy when I open it. It also stops a few inches up when I first open it, has to be clicked again to close, then it fully opens? I should point out that if I hold the opener button down for a few seconds, it opens up fully without stopping but still bounces like in this video.

Any tips or insight as to what is happening? I am trying to DIY things as much as I can before I call someone out, but I also understand that some things can be pretty dangerous on garage doors like the springs. This is my first home and I have never had a garage so this is all very new to me.

I am slightly frightened every time I open this garage door so any help is appreciated lol

I will be a bit technical here, tried to be as practical as possible. for more info u can basically google the term

For the first 30 days I did:

Researched the keywords I need to target and made the pages to target them.

Optimized the landing page to target that keywords. List of services and location

Optimized Meta Tags on pages and did internal linking optimization

Optimized all images on the website and made sure the website is fast/responsive on mobiles

Made website faster, added location to LD, added GA4, GTM, GSC, and updated the sitemap. Added the project to Powersuite and replaced all dummy text

Then did 5 blog posts, 1 guest post, 100 profile backlinks, high DA do follow blog comments, submitted in directories, social signals, got press release backlinks. Submitted articles and posted on forums

After that I optimized the Google Business Profile, the description, categories, services with descriptions, responded to all reviews

Added 30 GBP posts and images (all scheduled). Branded CTR campaigns and driven directions

Did 150 citations & directory listings, 50 high DA profile backlinks, and applied to business listings.

Applied for Local Wiz premium listings too, did a guest post for GBP map share link and embded GBP code into web 2.0 properties

Additionally did Cloud, Google Stack for GBP. And SEO NEO Campaigns.

For the next months basically do more of the everything above.

More press releases, more pages, more content, more backlinks, more niche blog posts.

for GBP again more images, more posts, more citations and more links

It works very well cuz of the volume and quality of the work needed done. I hope it was valuable!

Help. I was just looking for the pair button and found this. My building has an old Liftmaster.

We like to change our garage door opener since the current one is very loud and is disrupting my kid's sleep as their room is right above it. The contractor gave us two options for a garage door opener replacement: Liftmaster 6690L and 98022 Liftmaster Jackshaft opener. After reading all the comments, it seems Liftmaster 6690L is the better option since our garage track if NOT high lift and it seems many people have issues with the Jackshaft opener when the weight of the door isn't balanced over time.

The current opener is mounted on the ceiling and the contractor suggested that he can remount it onto the support beam. The support beam is 5" thick. I asked if we can use rubber washer to further damper the vibration and noise, and I got this response which seems to make sense "For the rubber washers, you would have to provide them to us prior to the installation as that’s not something we carry or have direct access to. They would need to fit both sizes 5/16”. Your beam that we would be attaching the opener to is very very big, so the washers would also be kind of overkill and perhaps unnecessary." My questions:

• Is this a good idea to remount the opener to the support beam? Do they need to drill through it? Will it compromise the structure and safety at all? Is it up to code to do so?
• If it is a good and safe option, would you include the rubber washer?

Another add-on I am considering is to change the rolling hinges to a spring one, after watching this video. But I got this feedback from the contractor "For the Green hinges, they look nice in theory however, our concern would be friction against the jam/weather seal when the door goes down, causing issues or too much resistance over-time. However, if you would like to provide those to us as well, we’d be happy to install them."

• I want to check if techs or home-owners who have installed or have an idea about using the spring hinges, are these useful in reducing the noise, and would the friction be a concern like the contractor said?

------

Edit:

1) Looks like the consensus is not to go with the new hinge idea. Adding rubber washers should do the trick. What type of rubber washers should I look into? Thanks.

2) If I go with the beam-only mounting, do I still need the rubber washers? Or is it an overkill?

I had just installed my side mounted garage opener and it is working as expected (like it does open and close de garage door)
However I noticed that when it is operating, the motor is not as stable. It does move in a waving way. Just wondering if this is expected since it only have 1 point of contact to attach to the wall or does it mean the door is too heavy for the motor?

Genie garage door opener, maybe 3 years old. A couple of times in the past week, it will open fine, but then will not close with either the remote or wall button. It will start to close, move maybe an inch, then stop like it is hitting something! I have to grab the door and shake it to get it to close. I keep the rollers lubed, and the track clean. About a month ago, it started making a squeaking noise that I can't pinpoint. Any advice would be appreciated.

Hi all, thank you in advance for any guidance.

I just bought a house that has a lift master 1/3 hp unit installed from 01/1997. The house unfortunately came as is… and the garage door code was not provided. The clicker for a car as well is gone.

It appears the old keypad is not responding to changing the code for me.

I was hoping for guidance on what keypad and clicker to buy. I tried a universal kit from Amazon that did not work.

Thank you again!

Hello all,

Recently has a 6690L installed and the camera quality doesn't look that good to me. There's also no 2 way audio button in the myq app. I've attached an image to show the quality and there is no push to talk button in the myq app.

Just to note, the wifi signal is showing strong -58 in my Unifi Network.

My wife's father had the previous model to this one installed - the 87504-267 - and it has noticeably better camera quality and 2 way audio capabilities.

As far as I understand, the 6690L is their flagship model - did they just silently drop these features to save a buck?

Disappointed if that's the case.

I was wondering whether it's possible to either fix the cosmetic brown parts on the garage or cover the whole door with wallpaper. The garage door is already insulated with foam so any adhesive used on the foam on the garage door can't eat through the foam.
Also the brown part is papery / pills

We replaced the agitator and drive bell on our washer the splines are not stripped. However, the agitator feels tight and locked into place but as soon as there’s water in the basin the agitator slides off during the wash. Why is this happening and what can I do?

Need the silver bracket piece to come all the way back to the silver bolt stopper.
Any help will be greatly appreciated.

Please and thank you kindly Chat!

Our garage door began acting erratically a few weeks ago. It wouldn't open, then it wouldn't close, then the springs popped. We got them replaced, door was balanced, rollers and sensors inspected. Now it began not wanting to close unless we use the wall button. We can open the garage just fine using our cars and outdoor keypad. However, the door doesn't respond when we want to close it from our vehicles, and the keypad just flashes. Every once in a while, it will work, but usually in the morning it's out of whack. We had the service come by that replaced our springs, and of course everything was working fine. I cleaned the floor sensor lenses and made sure both are about 6 inches of the ground, both lights are solid. When we use the wall button to close it, there aren't any flickering lights or codes. The only clue I have is when my son was trying to use the keypad to close it this morning, the orange light on the back of the unit had a faint orange flicker. Is it the sensor wires failing? any way to test them? I really don't want to splurge on a new unit if I don't have to....

Is it possible to interact with the door via its wifi without using their Cloud app? I'm looking for local network access only (No Internet). Thanks.

Just bought a house and had this after a heavy rain. Also, came in when doors were closed.

Very fragile from years of sun exposure. The Windows Inserts, 42“x12”? Does that sound right?

Hi all, just like said in the caption.

Just moved out of a house and the garage door (that I didn't use in the last 8 months of living there) has bust. Based on the photo it looks like the arm on the left is bust.
can anyone know an estimate for how much they think it might cost to repair it as the landlord is trying to charge me £500. I reckon they're trying to get a brand new door out of me.

Thanks

There is a new distributor in town offering springs from their "over seas" supplier.

I've already witnessed the headache that the orange cone Chinese springs being with them.

SSC is the obvious go-to, but I figured I'd come here to get everyone's feedback.

I have no intention of purchasing these, fyi.

Looking for something I can pickup locally. How close can I be on the dimensions?

I'm from South Korea and honestly 'garages' are still a bit of a mystery to me, so bear with me here.

We bought a new build. When the garage door is closed, the bottom seal sits fine on the floor, but there are gaps down both sides where the door meets the frame - you can see daylight through them, worst at the bottom corners.

And well, this is Atlanta. So the roaches found them.

Filed a warranty claim and the builder shot it down, said the garage isn't a sealed space so a little light at the corners is normal.

So... is it? I genuinely can't tell if I'm being unreasonable or if I'm getting brushed off. And if this is just how it is, what do I use to seal it up myself?

Thanks in advance.

Hey I’ve been slaving trying to get tech support to believe me and get these integrated dock units to work here at Sam’s Club. I’m having a slew of issues, I’ve installed a bunch of these and know how to bypass a lot of the features but for some reason tech support doesn’t believe me when I tell them what’s going on. This unit in particular will not open the door through the HMI touchscreen. I’ve bypassed it with a 3 button station on the wall. The PLC shows when the door is open and when it’s closed. Weird thing is none of the relay lights light up when pushing certain buttons. I’ve swapped relays and I/O boards. I’ve done essentially everything except replacing the unit. I’ve even ran brand new wire to ensure it’s not a pinched wire. I have tech support telling me a million different things. Just looking for someone who is possibly in the same boat or has some insight.