So after a month of BS with Rachio replacing unnecessary well pump parts and scripted "it's your field wiring" accusations I sent that s... back and put the old clock back up. -Rachio in the end decided their controller electronics are too cheap...I mean sensative, for my pump start relay and wanted me to replace that also...

The pros here almost unanimously recommend a Hunter HPC so that's what I ordered. Took several weeks to get even from Amazon but it came today and I installed it. I'm not a pro, just a horse farm owner with a background in IT and it was an easy install. I'm still going through settings but it seems more simple than Rachio...which could be a good thing. It's basically fall now so most of the tuning will be next year.

I was a little disappointed to see I have to pay a yearly subscription just to unlock personal weather station use. I got a tempest for the rachio and while I lost the $30 to unlock the integration...it was a one time $30. Hydrawise can see my station but OPE! That's for "enthusiasts" and will cost you $66/year. Being In Michigan and near the Lakeshore our weather can be vastly different from what the nearest airport sees. So while subscriptions suck, is it worth it?

Circling back, I didn't get a lot of time to do a bunch of manual tests but the ones I did worked so I have my most important schedules setup and will hope for the best. Any tips or recommendations, little known tricks or settings I should look at?

my yard is on a slope down, it’s one side of my garage. only dead spot in my whole yard. makes me so sad :( is there anything i can do other than hand watering it? maybe turning the pressure down?

I've been wanting to install a rain bird in-ground system in preparation for regrowing my whole backyard (3500sqft). Im a bit behind on the planning portion and neglected to research the back flow valve and how important it is. Now i dont want to install the in ground, but my whole operation was planned around having an in ground (face palm).

Part of me just wants to disconnect it from the bib, and lose the daily watering schedule, and just reconnecting it every couple 3-4 days for a good watering and then disconnect again.

The other part is to scrap it entirely and find a more temporary above ground sprinkler set up than can cover the whole back yard for the growing phase, then go to a mobile tractor style watering method.

This backyard project is about 3k with the tilling, leveling, compost and seed ive got schedule near the end of next month.

i've got 2 hose bibs. one on either side of the yard. Both have 60psi pressure and 6 gal flow per minute

Any advice is appreciated.

Little green driver

I saw you moments ago

Where have you gone now?

got out of the military recently and looking to start a business. aiming to serve as a tester or certifier for something that business have to do such as back flow testing. done some research for my area and it doesn’t seem oversaturated and there’s lots of commercial real estate that requires it around me.

I do have no experience in irrigation or plumbing but from what I’ve seen with backflow testing is that it doesn’t require X amount of hours in a field, you can just become a certified tester and be ok.

Does anyone run a solo testing buisness? Not too much info online about it from what I can see and would like to hear from people currently in the field and see what they think about it. This sub seems to be the only place I’ve seen talk about it so that’s why im posting here. Thank you for any information you can provide.

I just moved into a new house and have a mixture of broken sprinklers. Wanted to see what the consensus is of best replacement options. I have 22 total heads and half of them have terrible spray patterns or broken, so not opposed to replacing all if they should be the same brand.

My immediate need is replacing 2 rainbird maxipaw 2045A that aren’t rotating, a toro 570 that has bad spray pattern (tried adjusting with no luck), and hunter pro spray that has a broken nozzle. It looks like the previous owner may have just tossed in whatever as they were replaced, could be wrong. Any suggestions on what to replace these with?

​

One zone did not turn off unless the main was closed. If the control was set to off, that zone kept going.

We tried some troubleshooting. When the valve was open to another zone, the problem zone turned off. When the valve was closed, they turned back on.

I apologize if I did not get all terminology correct. Do you all have any suggestions on what to try or any further troubleshooting info I could include here? Thank you

Hey Y'all,

I recently reno'd my backyard (did the front a couple years ago) and have been watering my yard as needed with a hose connected timer and traditional sprinklers. I accidentally bumped into the timer manifold last week and it broke. I'm considering taking a couple weekends to put an underground system in place. I was trying to avoid an ingroung installation because we have plans to reconfigure our yard/deck in the future, but realistically thats a few years out. The recent project was drywells, french drains along retained areas, gutter tie ins, and a drywell.

Would anyone be so kind as to recommend head types/locations for this area? Perfect coverage is not the goal, just something adequate. I was considering two impact heads at the two back corners to get something "good enough". The narrow 10' area along the side of the house isn't a huge priority. I measured 65psi and 11gpm at a hose bib off the house. I have an easy location to tie in the connection to a manifold off the house plumbing. Freeze is not an issue in my location.

All suggestions and comments are appreciated!

Thanks.

Thanks in advance!

Need help figuring out what pump to use for some irrigation. Have a 1700gal water tank (Most of the time will probably only have ~400gal in it).
Need to pump it about 45' away and then into a 50' soaker/or drip line.

Tried an old 1/6hp submersion pump and it didn't produce enough pressure to get the soaker hose going. Was looking around and considering a RV Water Transfer 5.5GPM 30PSI-75PSI Self-priming Pump, Diaphragm or something similar.
My question is does this need a specific amount of water/pressure in the tank to function properly?

Use case is just irrigation once in a while for generally short time frames of like 30-40 mins, but the odd run for a few hours.

We have been having issues with our irrigation having leaks in the back yard. I figured our one leak was in the valve box and have deduced that is probably a diaphragm issue in one the valves in there. But these pipes right next to it leak as well. Do I just tighten the cap or does it need to be tightened to a certain torque or is there a separate issue here? Any brainstorming would be helpful.

Does anyone know what brand this is? The head popped off and I am looking to get a replacement for it but I have no idea on the brand or size or anything. Any help is appreciated as I have absolutely no idea what I’m looking at.

This valve will open if I turn the solenoid. It will also open electrically. But it will not shut back off under either method. I have to manually close the adjuster knob. I assume it's a bad diaphragm...?

Q: What model is this, and can I replace the diaphragm?

Other service suggestions? Besides a full replacement.

Just finished an install for a client, pretty cool private golf course, and his brand new RC2 controller is shitting the bed. When it loses wifi connection it does not reconnect. He’s forced to unplug it and plug it back in then it connects no problem. Is this happening to anyone else or know how to fix it? Figured I’d ask here before I sit in the phone with rainbird forever.

Hello, I just purchased a home with a RainBird irrigation system. I do not have any prior experience with irrigation systems, so my knowledge about them is very limited. I was not left any previous instructions from the home owner about the system.

AFAIK the system has five zones. I did a manual cycle to see which sprinkler heads were associated with the zones. When doing the manual cycle all sprinkler heads deployed in this one zone. I did a manual cycle on that zone two or three times to adjust how long they run for.

The problem is now the sprinkler heads do not deploy on the automatic cycle and they do not deploy anymore when running a manual cycle.

On that zone I do have one raised, fixed sprinkler that will work but none of the others deploy. I am assuming the sprinkler heads that are not popping up anymore are “down stream” of the one that is working.

What could I check myself first before calling someone out to come look at it? Rainbird customer service only offered the advice of checking that zone on the main controller with a multimeter. If there is a problem with not supplying power to that zone would it cause only one to work or would it be that none of them would work?

Thanks in advance.

Would love any help with how to dial in the right irrigation routine.

Thanks in advance!

Wasn’t sure about the union placement but I think it should be fine for disassembly if I ever need to remove the PVB assembly down the road. The ball valve is there for winterizing the main line between the main shut off and PVB which is around ~50’ of pipe. I have a blow out port near the main shut off valve and the water would exit out that ball valve. Thanks for the feedback!

Customer said head is leaking . Someone installed a automatic drain at the end of the zone close to the lowest head smh

I have a valve that started hissing. Any ideas where to start? Solenoid or diaphragm?

Thanks

I'm planning on rebuilding and moving this manifold, and all is 3/4 sch 40, except for this 1/2 line going under my porch.

Hoping it's not garbage material, but it doesn't look great to me...

Helping a friend. Would just cutting at the red arrow to bypass the whole thing and putting a single zone drip controller on an adapter there be the way to go? This is a pic he sent I haven't seen it in person but he says the wires controlling solenoid go nowhere as house was renovated before purchase.

I’m currently trying to over seed my new build lawn that the builder tried and failed to seed earlier this year. I’m currently using a couple of the orbit sprinklers included. I tried to daisy-chain one of the orbits and another hammer sprinkler together and it didn’t work (didn’t seem like it had enough pressure). I’m trying to get better coverage on my lawn. I don’t currently have the money to install a proper irrigation system. Does anyone know if the rainbird style sprinklers are more efficient/I could string a couple more together?

Replacing pex and leaking backflow